Minimum Guaranteed Power | ||||
per channel, both channels driven | ||||
XLS 1000 | XLS 1500 | XLS 2000 | XLS 2500 | |
Stereo, 2 ohms (per ch.) | 550W | 775W | 1050W | 1200W |
Stereo, 4 ohms (per ch.) | 350W | 525W | 650W | 775W |
Stereo, 8 ohms (per ch.) | 215W | 300W | 375W | 440W |
Bridge-Mono, 8 ohms | 700W | 1050W | 1300W | 1550W |
Bridge-Mono, 4 ohms | 1100W | 1550W | 2100W | 2400W |
Sensitivity (for full rated power at 4 ohms) | 1.4 Vrms |
Frequency Response (at 1 watt, 20 Hz - 20 kHz) | +0 dB, –1 dB |
Signal-to-Noise Ratio | Rated as dBr to full rated 8Ω power output (A-Weighted): |
XLS1000 > 97 dB | |
XLS1500, XLS2000, XLS2500 > 103 dB | |
Damping Factor (8 ohm): 10 Hz to 400 Hz | > 200 |
Crosstalk (below rated 8Ω power) | At 1kHz: > 85dB |
At 20kHz: >55dB | |
Input Impedance (nominal) | 20 kΩ balanced, 10 kΩ unbalanced |
Load Impedance | 2 to 8 Ω per channel in Stereo |
4 to 8 Ω in Bridge Mono | |
AC Line Voltage and Frequency Configurations Available (± 10%) | 120 VAC 60 Hz |
100 VAC 50/60 Hz | |
220 and 240 VAC 50 Hz | |
Ventilation | Flow-through ventilation from front to back |
Cooling | Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation |
Air Volume Requirements (per minute per unit) | 80.15 ft³ (2.27 m³) |
Integrated Processing | PureBand™ Crossover System |
Crossover Filter: Linkwitz-Riley 24dB per Octave | |
Crossover Frequency Range: 50 HZ - 3 kHz | |
Crossover Mode: Crossover (CH1=LPF, CH2=HPF), LowPass (both channels LPF), HighPass (both channels HPF), Bridge (LPF or HPF). | |
Peakx™ limiters: Channel independent clip limiter designed to | |
provide maximum output while protecting your loudspeakers | |
Input/Output | Input Connectors: XLR (one per channel), 1/4-Inch (one per channel), and RCA (one per channel). 1/4-Inch connectors can be used as loop-thrus to distribute signal to additional amplifiers. |
Output Connectors: Two 4-Pole Speakon® Output Connectors | |
accept 2-pole or 4-pole Speakon® connectors. The top Speakon connector is wired for both channels so it can be used for bridgemono wiring or for stereo wiring of two speakers to a single Speakon connector. | |
One pair of back-panel binding posts per channel; accepts | |
banana plugs or bare wire. (European models do not accept | |
banana plugs.) | |
Construction | XLS1000/XLS1500: 8.12-Inch (20.62cm) depth |
XLS2000/XLS2500: 10.35-Inch (26.29cm) depth | |
Dimensions | EIA Standard 19-inch (48.3-cm) rack mount width |
(EIA RS-310-B), 3.5-inch (8.9-cm) height. | |
XLS 1000/1500: 7.7-inch (19.6-cm) depth. | |
XLS 2000/2500: 10.7-inch (27.2-cm) depth. | |
Net Weight , Shipping Weight | XLS1000: 8.6 lb (3.9kg), 13.6 lb (6.2 kg) |
XLS1500: 8.6 lb (3.9kg), 13.6 lb (6.2 kg) | |
XLS2000: 10.75 lb (4.9kg), 15.8 lb (7.1 kg) | |
XLS2500: 10.75 lb (4.9kg), 15.8 lb (7.1 kg) |